PVDF 5000物性表

 

Hylar® 5000
聚偏二氟乙烯
Solvay Specialty Polymers

产品说明

Hylar 5000 is a crystalline high molecular weight powder form of polyvinylidene fluoride specifically designed for solvent-based coatings to provide improved gloss. It forms mechanically strong and tough films that have a broad useful temperature range. These films are highly resistant to most environmental conditions including gamma radiation and are essentially transparent to ultraviolet radiation. The weathering characteristics of Hylar 5000 coatings lead to excellent performance for the long term.

Hylar 5000 is available only via a licensing program that specifies the composition of Hylar 5000 coatings. A properly formulated finish contains sufficient pigment to make the film totally opaque to ultraviolet radiation at the nominal one mil (0.001 inch) film thickness suggested.

Safety
Hylar 5000 is stable at temperatures up to 600°F (316°C). When it is subjected to temperatures above 600°F (316°C) for extended periods of time, hydrogen fluoride (HF) begins to evolve, and at temperatures above 700°F (371°C) HF evolution becomes rapid. Hylar 5000 exhibits excellent flame resistance; however, in case of fire, HF and traces of potentially toxic fluorocarbons can be formed. HF is corrosive, causes burns on contact, and has an American Conference Governmental Industrial Hygienists (ACGIH) Threshold Limit Value (TLV-TWA) of 3 ppm (2.5 mg/m³) (1984).

Thermal decomposition of Hylar 5000 to HF can also occur in a bake oven in the event that temperatures are not controlled properly. In the event of fire, use NIOSH approved self-contained breathing apparatus and skin protection to protect against volatile decomposition products. Hylar 5000 can be disposed of in an approved land fill, but should not be incinerated unless permitted by applicable law and provision is made for absorption of HF.

总体

材料状态 • 已商用：当前有效   
供货地区 • 北美洲 • 欧洲  
 • 纯净/高纯度 • 抗辐射性 • 气味低到无 
性能特点 • 高分子量 • 抗紫外线性能良好  
 • 光泽，高 • 良好的强度 • 韧性良好 
    
 • 结晶 • 耐气候影响性能良好  
用途 • 薄膜 • 涂敷应用  
外观 • 白色   
形式 • 粉状   
加工方法 • 涂层   

物理性能 额定值单位制 测试方法
比重 1.75 到 1.76g/cm³ ASTM D792
吸水率 (平衡) 0.040% ASTM D570
Purity 2 > 99.5% 
含水量 - Karl Fisher 3 < 0.50% 
热性能 额定值单位制 测试方法
熔融温度 156 到 160°C ASTM D3418
热稳定性 4 382 到 393°C TGA
光学性能 额定值单位制 测试方法
Gardner光泽度 (60°) > 25 ASTM D523
充模分析 额定值单位制 测试方法
表观粘度 (232°C, 100 sec^-1) 29000 到 33000Pa•s ASTM D3835
补充信息 额定值单位制 测试方法
离散度 5 5.50 ASTM D1210

备注
1 一般属性：这些不能被视为规格。

2 polyvinylidene fluoride

3 non-hygroscopic

4 1% Wt. Loss in Air

5 Hegman Grind

 

 


1 / 1