FEP 100

 

Teflon® FEP 100
聚全氟乙烯-丙烯树脂
DuPont Fluoropolymers

产品说明

TEFLON® FEP 100 fluorocarbon resin is a meltprocessible fluorocarbon resin suitable for extrusion as a primary coating onto most gauge wires (AWG #12 and smaller) for twisted-pair constructions and for limited jacketing applications.

This resin provides the electrical and mechanical properties needed for low voltage applications. TEFLON FEP 100 has a melt flow rate that is between TEFLON 3100 and TEFLON FEP 140. This permits a good combination of extrusion speed and stress crack resistance, making TEFLON FEP 100 the insulation of choice for most primary insulation that is more than 7 mils thick.

TEFLON FEP 100 possesses a balance of processing and performance properties which make it the preferred resin for many applications. Like all TEFLON fluorocarbon resins, TEFLON FEP 100 offers an excellent combination of properties: chemical inertness, exceptional dielectric properties, heat resistance, toughness, flexibility, low coefficient of friction, nonstick characteristics, negligible moisture absorption, low flammability, performance at temperature extremes, and weather resistance.

总体    
材料状态 • 已商用：当前有效   
供货地区 • 北美洲 • 欧洲  
 • 低摩擦系数 • 耐气候影响性能良好 • 吸潮性差 
性能特点 • 良好的柔韧性 • 耐热性，高  
 • 耐化学性良好 • 韧性良好  
用途 • 电缆护套 • 电线电缆应用  
形式 • 颗粒料   
加工方法 • 挤出   

物理性能 额定值单位制 测试方法
比重 2.14g/cm³ ASTM D792
熔流率 (372°C/5.0 kg) 6.6g/10 min ASTM D1238
机械性能 额定值单位制 测试方法
抗张强度 (屈服) 27.6MPa ASTM D638
伸长率 (断裂) 340% ASTM D638
热性能 额定值单位制 
熔融温度 264°C 
电气性能 额定值单位制 测试方法
介电强度  ASTM D149
0.254 mm 79kV/mm 
3.18 mm 20kV/mm 
介电常数  ASTM D150
100 kHz 2.06 
1 MHz 2.06 
耗散因数  ASTM D150
100 kHz 0.00030 
1 MHz 0.00060 
  
挤出 额定值单位制 
第1气缸区温度 366°C 
第2气缸区温度 382°C 
第3气缸区温度 388°C 
第4气缸区温度 393°C 
第5气缸区温度 396°C 
连接器温度 396°C 
熔体温度 393°C 
模具温度 416°C 
挤压说明  
Processing conditions for extruding Teflon® FEP 100 on AWG #24 Solid Copper Wire  
60 mm Extruder with 30:1 L/D  
Clamp Temperature: 745°F  
Crosshead Temperature: 745°F  
1 / 2  
  
 
 
 
  
 
Teflon® FEP 100 2012年9月30日
聚全氟乙烯-丙烯树脂
DuPont Fluoropolymers
备注

1 一般属性：这些不能被视为规格。